Araldite Standard vs Araldite Klear5: Which One Should You Buy?

May 4, 2026

Summary

The primary difference between Araldite products is strength versus aesthetics. Araldite Standard is stronger but cures an opaque off-white, while Araldite Klear5 creates a completely transparent bond.
Choose Araldite Standard for high-stress, structural repairs on materials like metal where its superior 30 MPa strength is critical and the bond line will be hidden.
Opt for Araldite Klear5 for aesthetic fixes on glass, ceramics, or wood veneer where its invisible finish and fast 5-minute set time are more important than maximum strength.
To ensure you get 100% genuine products for your project, order Araldite Standard and Klear5 from HomeRun for 60-minute delivery across Bangalore.

You're staring at two Araldite products on the shelf — or scrolling through an online store — and you're stuck. Both are two-part epoxies. Both come from the same trusted brand. Both promise a strong, reliable bond. So what's actually different, and which one is right for your job?

It's one of the most common adhesive dilemmas facing DIYers, carpenters, and fabricators in Bangalore today. As one Reddit user put it bluntly: "It depends on the job. What do you need it for?" — and that's exactly the question this guide will answer.

Whether you're a carpenter finishing a veneer edge, a fabricator fixing a metal bracket under load, or a homeowner trying to invisibly repair a glass shelf, picking the wrong Araldite can mean a visible, ugly bond line — or worse, a joint that fails under stress. This head-to-head comparison will end the confusion for good.

Quick note for Bangalore buyers: If you need to check the araldite price list Bangalore, or simply get both SKUs delivered to your site without risking counterfeit stock, HomeRun delivers 100% genuine Araldite — Standard and Klear5 — in 60 minutes across 105+ pin codes.

What Is a Two-Part Epoxy? (A 60-Second Primer)

Before we dive into the comparison, it helps to understand what makes Araldite special in the first place.

Both Araldite Standard and Araldite Klear5 are two-part epoxy adhesives, meaning they consist of two separate components: a resin and a hardener. When you squeeze out equal parts of each and mix them together, a chemical reaction begins — one that produces a bond that is rigid, waterproof, heat-resistant, and significantly stronger than most single-component adhesives.

This chemistry is what gives Araldite its reputation. Unlike PVA or contact cement, once a two-part epoxy cures, it doesn't just stick — it forms a near-permanent molecular joint. That's why it's the go-to for structural repairs, not just surface-level fixes. As fans on Reddit note, "Araldite is my go-to for small jobs around the house... have used it on multiple projects without it failing."

The real difference between the two products comes down to strength vs. clarity — and understanding that trade-off is everything.

Araldite Standard vs. Araldite Klear5: Head-to-Head Comparison

Here's the complete breakdown you need before buying:

Feature	Araldite Standard	Araldite Klear5
Cure Time	Full strength in 24 hours	Initial set in 5–10 minutes; full strength in 5–6 hours
Working Strength	Up to 30 MPa — extremely strong	Up to 25 MPa — very strong
Colour (Post-Cure)	Off-white / Opaque — bond line is visible	Perfectly clear / Transparent — invisible bond
Best Surface Suitability	Wood, Metal, Ceramic	Glass, Metal, Wood, Ceramic, some Plastics
Key Use Case	High-strength structural bonds where appearance is secondary	Aesthetic or visible repairs requiring an invisible join
Available Pack Sizes	15g, 25g, 50g, 100g	15g, 25g, 30g, 200g, 450g, 1.08kg
Relative Pricing	More economical	Premium pricing

Specifications synthesised from go-araldite.com, the Araldite India product brochure, and the HomeRun Araldite Klear5 product page.

The headline takeaway: Standard wins on raw strength. Klear5 wins on clarity and speed. For specific cost differences, you can review the latest adhesive price list. Now let's see what that means in practice.

Which Araldite Should You Use? Three Real-World Scenarios

Scenario 1: The Carpenter Bonding a Veneer Edge

The situation: You're finishing a high-end wardrobe panel and need to bond a thin veneer edge strip to the substrate. The bond needs to be strong, but the finish is just as important — your client will see every millimetre of that edge.

The choice: Araldite Klear5.

Araldite Standard does bond wood well, but its off-white, opaque colour can telegraph right through a thin veneer, leaving a discoloured ghost line that ruins the finish of premium furniture. Araldite Klear5, with its fully transparent cure, creates an invisible bond that doesn't interfere with the natural wood tone or the applied laminate. For carpenters working on visible joinery and furniture, Klear5 is the professional's choice — it bonds wood just as reliably while keeping the aesthetics spotless.

Bonus: Klear5's 5–10 minute initial set is also a production advantage on a busy site — you're not clamping and waiting 24 hours.

Scenario 2: The Fabricator Repairing a Metal Bracket

The situation: A metal angle bracket supporting a shelf has cracked at the weld. It's a structural component that's going to take real load. Speed is irrelevant — what matters is that the repair doesn't fail in six months.

The choice: Araldite Standard.

This is exactly what Araldite Standard was engineered for. At up to 30 MPa working strength, it outperforms Klear5 (25 MPa) in high-stress, metal-to-metal applications. The Araldite India brochure confirms it is the preferred product for metal owing to its high strength and durability. The fact that it cures off-white is completely irrelevant for a functional bracket that will be hidden or painted over. When you need the bond to hold, Standard is non-negotiable.

Scenario 3: The Homeowner Fixing a Glass Shelf or Ceramic Vase

The situation: A cherished glass shelf bracket has chipped, or a ceramic vase that belonged to a family member has snapped in two. The repair has to be strong — but more than anything, it has to be invisible.

The choice: Araldite Klear5. No question.

Using Araldite Standard here would be a mistake. Its off-white cure would leave a clearly visible scar across a transparent glass surface or a light-coloured ceramic glaze. Araldite Klear5, as detailed on its product page, delivers a "clear transparent finish," making it the go-to for glass repairs and any application where the bond line must disappear. The result: a strong, durable repair that restores the item's original appearance.

Pro Guide: How to Get a Perfect Bond Every Time

Choosing the right product is half the battle — application technique is the other half. Both products follow the same process, but getting it right is what separates a bond that lasts decades from one that fails in weeks.

Prepare the surface: Clean both surfaces thoroughly. Remove dust, grease, old adhesive, and any moisture. For smooth materials like glass or metal, lightly abrading the surface with fine sandpaper dramatically improves adhesion.
Dispense equal parts: Squeeze out equal amounts of resin and hardener onto a clean, disposable mixing surface (a piece of cardboard or a plastic lid works well).
Mix thoroughly: Blend the two components together for a minimum of one full minute until the mixture is completely uniform in colour and consistency. Incomplete mixing is the single biggest cause of epoxy bond failure.
Apply and join swiftly: Apply a thin, even layer to both surfaces, then bring them together firmly. You have a short working window — especially with Klear5.
Hold and clamp: Keep the pieces firmly in position without movement. Use clamps, tape, or a weight as needed. Any shift during the initial set phase weakens the final bond.
Cure fully before loading: Allow Klear5 to reach full strength over 5–6 hours. For Araldite Standard, wait the full 24 hours before putting the joint under any stress.

Pro tip from the community: Both Araldite products are available in a twin-syringe dispenser format, which dispenses equal parts of resin and hardener simultaneously. As one experienced user noted, "The twin syringe version makes mixing it perfectly a breeze" — you get the critical 1:1 ratio right every time, with zero measuring and minimal waste. It's well worth choosing this format if you're doing precision work.

The Final Verdict

Still not sure? Here's the one-line summary for each:

Choose Araldite Standard if:

You need maximum bonding strength (30 MPa) for structural or load-bearing repairs
You're bonding metal, wood, or ceramics where the joint won't be visible
You want a more economical price per gram for a high-performance result

Choose Araldite Klear5 if:

You need a transparent, invisible bond — especially on glass, clear materials, or exposed woodwork
You need a faster initial set time (5–10 minutes) to keep your work moving
You're working across a wider range of materials, including some plastics

When in doubt? Buy both. Standard for the heavy-duty structural repairs, Klear5 for the aesthetic and glass/ceramic jobs. Together they cover almost every bonding scenario you'll face on a construction or interior project.

Frequently Asked Questions

What is the main difference between Araldite Standard and Araldite Klear5?

The main difference is a trade-off between strength and aesthetics. Araldite Standard offers superior bonding strength (30 MPa) and is ideal for structural repairs where the bond line is not visible. Araldite Klear5 provides a slightly lower strength (25 MPa) but cures completely transparent and sets much faster, making it perfect for aesthetic repairs on glass, ceramics, or visible woodwork.

Which Araldite is stronger?

Araldite Standard is the stronger of the two. With a working strength of up to 30 MPa, it is engineered for high-stress, load-bearing applications, particularly metal-to-metal bonds. While Klear5 is very strong, Standard is the go-to choice when maximum durability and load capacity are the primary requirements.

How long does Araldite take to fully cure?

Curing times vary significantly between the two products. Araldite Klear5 is a fast-setting epoxy that reaches full strength in approximately 5-6 hours. Araldite Standard is a slow-cure epoxy that requires a full 24 hours to achieve its maximum bond strength and should not be put under stress before then.

Is Araldite waterproof after curing?

Yes, both Araldite Standard and Klear5 are fully waterproof and chemical-resistant once they have cured completely. This property makes them excellent for a wide range of repairs, including those that may be exposed to water or humidity.

Can I use Araldite on all types of plastic?

Araldite Klear5 is suitable for some plastics, but not all. Epoxies generally do not bond well with low-surface-energy plastics like polyethylene (PE) and polypropylene (PP). For best results, it's recommended to test the adhesive on a small, non-visible area of the plastic first to ensure proper adhesion.

What is the best way to mix Araldite?

The best way to ensure a perfect 1:1 ratio is by using the twin-syringe dispenser, which automatically dispenses equal parts. If using tubes, squeeze out two equal-length lines of the resin and hardener onto a clean, disposable surface. Mix them together thoroughly for at least one minute until the colour and consistency are completely uniform. Incomplete mixing is the most common cause of bond failure.

Can you paint over cured Araldite?

Yes, you can paint over Araldite once it has fully cured. To get the best paint adhesion, it's a good practice to lightly sand the cured epoxy surface to create a rough texture. This helps the paint or primer grip the surface for a more durable finish.

Get Genuine Araldite in Bangalore in 60 Minutes

Here's the problem no one talks about: counterfeit and expired adhesives are a real risk when buying from unverified sources. An epoxy adhesive that's been stored incorrectly or has passed its shelf life simply won't cure properly — and you won't know until your repair fails. That's a costly mistake on a fabricated bracket. On a glass shelf, it's a safety hazard.

HomeRun — Bangalore's quick commerce platform for construction and interior materials — sources 100% genuine Araldite Standard and Araldite Klear5 directly from authorised dealers. No counterfeits, no expired stock, just products you can trust to perform exactly as specified.

✅ Both SKUs available — Standard and Klear5 in stock and ready to ship
✅ 60-minute delivery across 105+ Bangalore pin codes (Whitefield, HSR Layout, Jayanagar, Hebbal, Rajajinagar, MG Road, and more)
✅ Authenticity guaranteed — sourced exclusively from authorised dealers
✅ One-stop shop — add Fevicol, plywood, hardware fittings, or anything else you need to the same order

Don't let a missing tube of adhesive stall your project or your workforce. Stop searching multiple stores, skip the risk of fake products, and get exactly what you need — right when you need it.

👉 Shop Araldite & the complete adhesives range on HomeRun now

Back to blog